Plumbing Basics: Before Bathtub Installation
Plumbing Basics: Before Bathtub Installation
Blog Article
The article author is making a number of great observations on the subject of A Step-by-Step Guide to Installing a Bathtub as a whole in this post down below.
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably challenging task. If the old bathtub is conveniently easily accessible, the project can move speedily; if you have to open a wall to remove the old tub and place the new bathtub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a service provider to take over a halfway-completed task, it is better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This short article will help you mount a brand-new bath tub in your shower room if you have already bought a brand-new bathtub and also don't need to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist should make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing the two wood boards under its feet, position the tub in the needed position. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub till the level reads level.
To mount taps, fit the bottom of the outermost versatile faucet port to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water supply as well as check all joints as well as new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the bath tub has actually been used at least once as this will certainly resolve it into its final setting.
Planning for the Installation
Firstly, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the tub remains in usage. The sealant can split relatively early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the market. It is recommended to fit the floor tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very taken with A Step-by-Step Guide to Installing a Bathtub and I hope you liked the page. Sharing is caring. One never knows, you may be helping someone out. I treasure reading our article about Tools You Need to Install a New Bathtub .
Schedule A Service Call Report this page